高级搜索 标王直达
排名推广
排名推广
会员中心
会员中心
 
发布信息当前位置: 首页 » 供应 » 机械及行业设备 » 阀门 » 气动阀 »

3A210-08气动阀/晋州市亚德客气动阀厂家

3A210-08气动阀/晋州市亚德客气动阀厂家
3A210-08气动阀/晋州市亚德客气动阀厂家3A210-08气动阀/晋州市亚德客气动阀厂家3A210-08气动阀/晋州市亚德客气动阀厂家
点击图片查看原图
品牌: 亚德客AirTac
单价: 面议
起订: 1 台
供货总量: 1000 台
发货期限: 自买家付款之日起 2 天内发货
所在地: 广东 广州市
有效期至: 长期有效
最后更新: 2017-03-16 09:46
浏览次数: 145
询价
公司基本资料信息
 
 
产品详细说明
3A210-08气动阀/晋州市亚德客气动阀厂家
Pneumatic valve features:
1, sliding column structure, good sealing, sensitive reaction;
2, double head air control with memory function;
3, the use of special processing holes, friction resistance, low starting pressure, long service life;
4, no oil lubrication;
5, multi position installation, easy to install and use;
6, can be integrated with the base valve group, saving installation space
气动阀特点:
1、滑柱式结构,密封性好,反应灵敏; 
2、双头气控具有记忆功能; 
3、内孔采用特殊工艺加工,磨擦阻力小,启动气压低,使用寿命长; 
4、无需加油润滑; 
5、多位置安装,安装使用方便; 
6、可与底座集成阀组,节省安装空间
 
3A210-08气动阀/晋州市亚德客气动阀厂家
Installation and use:
1, pay attention to check before using the components in the transport process is damaged, and then install;
2, please note that the installation of gas flow direction and the right type of nozzle. The media must be filtered through 40 M filter;
3, please note that the installation conditions are in line with the technical requirements (such as voltage, frequency of action, working pressure, the use of temperature range, etc.);
4, pay attention to the direction of gas flow in the installation, P position air inlet, A (B) working port, R (S) position air inlet;
5, try to avoid the use of vibration environment, and pay attention to antifreeze measures at low temperature;
6, the connection of the pipeline, pay attention to the tape can not be more than the end of the interface teeth, pay attention to clear the pipe joints dust, iron filings and other dirt, to avoid impurities or foreign body into the valve body;
7, please pay attention to dust, the exhaust port is recommended to install silencer or muffler throttle valve. When not in use should be installed in the inlet and outlet of the dust jacket.
安装与使用
1、使用前注意检查组件在运输过程中是否损坏,然后安装;
2、安装时请注意气体流动方向及接管牙型是否正确。使用介质必须经过40μM滤芯过滤;
3、请注意安装条件是否符合技术要求(如电压、动作频率、工作压力、使用温度范围等,)然后安装使用;
4、安装时注意气体流动方向,P位进气口、A(B)位工作口、R(S)位进气口;
5、尽量避免在震动的环境下使用,并注意低温下的防冻措施;
6、连接管路时,注意止泄带缠绕不可超过接口牙端面,注意清除管路接头内的粉尘、铁屑等脏物,避免杂质或异物进入阀体内;
7、请注意防尘,建议排气口安装消声器或消声节流阀。拆下不用时应在进、出气口装防尘套。
 
 
更多»本企业其它产品

[ 供应搜索 ]  [ 加入收藏 ]  [ 告诉好友 ]  [ 打印本文 ]  [ 违规举报 ]  [ 关闭窗口 ]