点击图片查看原图
作轨迹附着在滚道表面不很属于，从而改变了载荷条件。拆下轴承时，应严格观察并观察南京NSK轴承滚道表面轨道。假设轨迹被仔细观察，则只有径向载荷、大的轴向载荷、扭矩载荷或轴承箱上的刚度不等式是已知的。它可以用来检查轴承是否可以添加到试验载荷和偏差设备，并可以作为线索轴承损坏的原因，国立大学。图6-1示出了深沟球轴承在不同载荷条件下的工作轨迹。
Bearing rolling trajectory and loading method, the surface of internal and external raceways because of rolling contact with rolling elements, so the working trajectory is dark, the working trajectory attached to the raceway surface is not very belong to, thus changing the load conditions. When the bearing is removed, the surface track of Nanjing NSK bearing raceway should be observed and observed strictly. Assuming that the trajectory is carefully observed, only radial loads, large axial loads, torque loads, or stiffness inequalities on the bearing box are known. It can be used to check whether bearings can be added to test loads and deviation equipment, and can be used as a cause of clue bearing damage, National University. Fig. 6-1 shows the working trajectories of deep groove ball bearings under different load conditions.
（a）当内圈发生变化时，正常工作轨道仅承受径向载荷。（c）~（h）所示的工作轨迹对南京NSK轴承的影响较小，使用寿命相对较短。滚子轴承的工作轨迹是相同的。（1）内圈负荷变化时，圆柱滚子轴承的工作轨迹发生变化。当径向载荷增大时，圆柱滚子轴承外圈的工作轨迹更加。(j)内外圈须倾斜，轴挠度大于轨道，轨道在滚道表面上，轨道在负载环出口处的阴影的纵向舱口处倾斜，双列圆锥滚子轴承改变内圈。K意味着只有外环的工作轨道被加载在径向载荷上。L表示轨道仅承受轴向载荷。当内环和外环明显倾斜且仅承受南京NSK轴承径向载荷时，轨迹偏离两个轨迹平面180。
(a) when the inner ring changes, the normal working track only bears radial load. (c) the track shown in ~ (H) has little effect on the NSK bearing in Nanjing, and the service life is relatively short. The working track of roller bearings is the same. (1) when the inner ring load changes, the working track of cylindrical roller bearings changes. When the radial load increases, the working track of cylindrical roller bearing outer ring is more. (j) The inner and outer rings must be tilted, the shaft deflection is greater than the track, the track is on the raceway surface, the track is tilted at the longitudinal hatch of the shadow at the exit of the load ring, and the double row tapered roller bearings change the inner ring. K means that only the working track of the outer ring is loaded on the radial load. L indicates that the track only bears axial load. The trajectory deviates from the two trajectory planes 180 when the inner and outer rings tilt obviously and only bear the radial load of Nanjing NSK bearing.
文章来自：南京SKF轴承 www.wh-skf.com
The article is from: Nanjing SKF bearing www.wh-skf.com
文章来自：南京INA轴承 www.ina-china.cn
The article is from: Nanjing INA bearing www.ina-china.cn
文章来自：南京NSK轴承 www.klbbearings.com
The article is from: Nanjing NSK bearing www.klbbearings.com
QQ：524085168
电话：0510-81207777
手机：13311666672
