点击图片查看原图
General requirements for Yangzhou INA bearing lube oil
（1）减少摩擦磨损，降低摩擦阻力，节约能源，减少磨损，延长扬州INA轴承的使用寿命，提高经济效益。
(1) Reduce friction and wear, reduce friction resistance, save energy, reduce wear and tear, prolong the service life of Yangzhou INA bearing, improve economic benefits.
（2）需要冷却，以随时从机器上去除摩擦热。
(2) cooling is needed to remove frictional heat from the machine at any time.
（3）需要密封、防漏和防尘，以防止气体窜流。
(3) seal, leak proof and dust-proof are required to prevent gas channeling.
（4）腐蚀与防锈。有必要保护扬州INA轴承摩擦表面免受腐蚀或外部腐蚀。
(4) corrosion and rust prevention. It is necessary to protect the friction surface of INA bearing in Yangzhou from corrosion or external corrosion.
（5）清洗、清洗、清洗和去除摩擦面积。
(5) cleaning, cleaning, cleaning and removing the friction area.
（6）应力分散缓冲器、分散载荷、减震和减震。
(6) stress dispersion buffer, dispersed load, shock absorption and shock absorption.
（7）动能传递、液压系统、遥控马达和摩擦无级变速器。
(7) kinetic energy transfer, hydraulic system, remote control motor and friction CVT.
（a）油浴润滑
(a) oil bath lubrication
扬州INA轴承油浴润滑是zui 常用的润滑方法之一，适用于中低速轴承。使用该方法时，应注意控制油量，油面高度应略低于下轴承滚动轴承的中心线。过多的油会引起过高的温度扰动，而油的缺乏会导致轴承早期失效。
Yangzhou INA bearing oil bath lubrication is one of the most commonly used lubrication methods, suitable for middle and low speed bearings. When using this method, attention should be paid to controlling the oil volume, and the oil surface height should be slightly lower than the centerline of the rolling bearing of the lower bearing. Too much oil will cause excessive temperature disturbance, and the lack of oil will lead to early failure of bearings.
（b）喷油润滑
(b) oil spray lubrication
当扬州INA轴承在低速和中等负荷下高速运转时，滚子和保持架的转动使空气以相当大的速度围绕轴承旋转。为了保证向高速轴承提供足够数量的润滑油，润滑油必须从轴承的一端喷洒到轴承并润滑轴承，然后油从另一端重新流入油箱。润滑油的喷射速度不应低于15米/秒，油将直接注入轴承。
When Yangzhou INA bearings operate at high speeds at low and medium speeds, the rotation of rollers and cages causes air to rotate around the bearings at considerable speeds. To ensure that a sufficient quantity of lubricating oil is provided to the high speed bearing, the lubricating oil must be sprayed from one end of the bearing to the bearing and lubricate the bearing, and then the oil is re flowing into the tank from the other end. The injection speed of the lubricating oil should not be less than 15 m / sec, and the oil will be injected directly into the bearing.
（c）油滴润滑
扬州INA轴承润滑油是通过将润滑油的重量逐个减少到摩擦副来润滑的。这种润滑方法适用于少量容易接近的摩擦副。当轴承部件需要润滑油时，润滑油滴可以被润滑。滴油量通常为每滴3 s～8 s，过多的油会增加轴承的温升。
（d）循环油润滑
当扬州INA轴承转速较高时，轴承温升相应增加，导致油的老化。循环油润滑能有效地防止上述现象的发生。润滑油通过油泵送到轴承部，在轴承的另一端设置有油出口。轴承润滑油经过滤冷却后可循环使用。该方法适用于高速轴承零件。但是注意，油出口应该大于油入口，这样就不会在轴承座中留下剩余的油。
文章来自：扬州SKF轴承 www.wh-skf.com
The article comes from: Yangzhou SKF bearing www.wh-skf.com
文章来自：扬州INA轴承 www.ina-china.cn
The article comes from: Yangzhou INA bearing www.ina-china.cn
文章来自：扬州NSK轴承 www.klbbearings.com
The article comes from: Yangzhou NSK bearing www.klbbearings.com
QQ：524085168
电话：0510-81207777
手机：13311666672
