点击图片查看原图
Lubricating Yangzhou INA bearing repair method: lubricating oil in bearings can be broadly divided into two kinds: lubricating oil and grease.
修复方法：制备：干毛巾、尖头钳、轴承清洗夜、扬州INA轴承润滑剂或润滑脂。
Repair method: preparation: dry towel, pointed tongs, bearing cleaning night, Yangzhou INA bearing lubricant or grease.
1，干燥：从清洗液中取出轴承，用干毛巾擦拭清洁液，然后在阴凉处晾干。
2，扬州INA轴承清洗液：将轴承浸入市场中轴承的清洗液中，然后将其扔掉，轴承中的异物会摆动，一些商店购买的超声波清洗机也有助于清除异物。
2, Yangzhou INA bearing cleaning fluid: immerse the bearings in the cleaning liquid of the bearing in the market, then throw them away, the foreign objects in the bearings will swing, and the ultrasonic cleaning machines purchased by some stores also help to clear the foreign objects.
3，注入扬州INA轴承润滑剂，根据趋势向轴承内注入油或油，覆盖保护盖并重新安装C环。
4，拆下C环和保护罩：用干毛巾擦拭轴承外圈，然后用锋利的钳子握住C环的侧面，并取C环和屏蔽罩。
4, remove the C ring and protective cover: wipe the outer ring of the bearing with a dry towel, then use the sharp pliers to hold the side of the C ring, and take the C ring and shielding cover.
5，试验：扬州INA轴承的初始状态用手指组装，内圈反复转动。
5, test: the initial state of INA bearing in Yangzhou is assembled by fingers, and the inner ring is rotated repeatedly.
离心式阻尼器的双质量扬州INA轴承飞轮可安装在传统双质量飞轮的原空间中，隔振率可达到90%以上，并具有扬州INA轴承弹簧质量系统的基本隔振功能。这使得发动机能够以非常稳定和舒适的方式运行，从而进一步提高传动比和节省燃料消耗。该产品可通过手动变速器和双离合器变速器进行操作。
The double mass Yangzhou INA bearing flywheel of the centrifugal damper can be installed in the original space of the traditional double mass flywheel, and the vibration isolation rate can reach more than 90%, and it has the basic vibration isolation function of the INA bearing spring quality system of Yangzhou. This enables the engine to operate in a very stable and comfortable manner, thereby further improving the transmission ratio and saving fuel consumption. The product can be operated by manual transmission and dual clutch transmission.
滚动轴承是精密零件，应慎重使用。即使轴承被误用，也不能达到预期的效果。
即使是肉眼看不见的微小灰尘也会对扬州INA轴承产生不良影响。因此，保持周围的清洁，使灰尘不会侵入轴承。
Even tiny dust that is invisible to the naked eye will have an adverse effect on Yangzhou INA bearings. Therefore, keep the surrounding clean so that the dust will not invade the bearings.
在使用过程中对轴承的强烈影响将导致疤痕或压痕，并导致事故。在严重的情况下，必须注意裂纹和断裂。
The strong impact on bearing during use will lead to scar or indentation and cause accidents. In severe cases, cracks and breakages must be noted.
当扬州INA轴承运行时，手汗会生锈。注意使用干净的手，尽可能多地使用手套，注意腐蚀性气体。
When the Yangzhou INA bearing runs, the hand sweating will rust. Pay attention to using clean hands, use gloves as much as possible, and pay attention to corrosive gases.
文章来自：扬州SKF轴承 www.wh-skf.com
The article comes from: Yangzhou SKF bearing www.wh-skf.com
文章来自：扬州INA轴承 www.ina-china.cn
The article comes from: Yangzhou INA bearing www.ina-china.cn
文章来自：扬州NSK轴承 www.klbbearings.com
The article comes from: Yangzhou NSK bearing www.klbbearings.com
QQ：524085168
电话：0510-81207777
手机：13311666672
